Product Details:
Payment & Shipping Terms:
|
| POE Standard: | Supports PoE IEEE 802.3af Compliant PDs | Switch Type: | POE Switch |
|---|---|---|---|
| Bandwidth: | 20Gbps (non-blocking) | PoE Port Power: | 15.4W For Each POE Port |
| Power Supply: | Power Input: AC100-240V 50/60Hz; (every Country Use A Custom Power Plug) | Ports: | 10*10/100/1000 Mbps Ports With AutoUplink |
10/100/1000Mbps 10 Port Ethernet POE switch 24V/48V IEEE802.3af/at for IP camera
How does POE work?
Network cables, such as Cat 5e and Cat 6, comprise eight wires arranged as four twisted pairs. In 10 and 100BASE-T Ethernet, two of these pairs are used for sending information, and these are known as the data pairs. The other two pairs are unused and are referred to as the spare pairs (Gigabit Ethernet uses all four pairs).
Because electrical currents flow in a loop, two conductors are required to deliver power over a cable. POE treats each pair as a single conductor, and can use either the two data pairs or the two spare pairs to carry electrical current.
Power over Ethernet work
Power over Ethernet is injected onto the cable at a voltage between 44 and 57 volts DC, and typically 48 volts is used. This relatively high voltage allows efficient power transfer along the cable, while still being low enough to be regarded as safe.
This voltage is safe for users, but it can still damage equipment that has not been designed to receive POE. Therefore, before a POE switch or midspan (known as a PSE, for power sourcing equipment) can enable power to a connected IP camera or other equipment (known as a PD, for powered device), it must perform a signature detection process.
Signature detection
Signature detection uses a lower voltage to detect a characteristic signature of IEEE-compatible PDs (a 25kOhm resistance). Once this signature has been detected, the PSE knows that higher voltages can be safely applied.
10 ports POE ethernet switch
10 ports 10/100/1000M POE Switch is a Gigabit POE Switch,Which is cost-effective provide network layout need to simplify wireless access point (AP) and IP-based surveillance cameras network cameras in order to install in commercial network and home network. The devices far away from power socket are very suitable for hanging on the wall or ceiling. PoE eliminates the need for connecting these devices to power socket. So it make more flexible for those difficult to connect with AC power socket, and cut down the installation cost. It is ideal choice for those want to deploy a small commercial network and home network that use wireless access point (AP) and IP-based surveillance cameras.
Features
◆ IEEE 802.3af power on up to 8 ports
◆ Supply power to wireless access points and surveillance cameras over Cat-5 cabling
◆ 10*10/100/1000 Mbps Ports with AutoUplink™
◆ Supports PoE power up to 15.4W for each PoE port
◆ Supports PoE power up to 150W for all PoE ports
◆ Supports PoE IEEE 802.3af compliant PDs
◆ Supports IEEE 802.3x flow control for Full-duplex Mode and back pressure for Half-duplex Mode
◆ 1K entry MAC address table of the PoE Switch with auto-learning and auto-aging
◆ LED indicators for monitoring power, link
◆ Support Vlan and Extend Function
◆ Internal power adapter supply
Specification
 Technical parameter list |
|
| Product Name | 10-Ports AF PoE Switch with 8 PoE Ports and 2 Gigabit Uplink |
| Connector Type | 10* 10/100/1000M copper cable RJ45 ports(8 PoE ports+2 Uplink) |
| Network Media | 10BASE-T: Cat3,4,5 UTP(≤100 meter) 100BASE-TX: Cat5 or more UTP (≤100 meter) |
| Bandwidth | 20Gbps (non-blocking) |
| Address Database Size | 8K |
| MTBF | 190,000 hours (about 21 years) |
| Forwarding Mode | Store-And-Forward |
| Network Protocols |
IEEE 802.3i 10BASET; IEEE 802.3u 100BASETX; IEEE 802.3x Flow Control; IEEE 802.1af DTE Power via MDI; IEEE 802.3af |
| LED Display | System: power supply; Every Port: connecting, PoE working status |
| Power Supply | Power input: AC100-240V 50/60Hz; (every country use a custom power plug) |
| PoE Ports | Port 1-8 support POE |
| PoE Port Power | 15.4W for each POE port |
| PoE Standard | IEEE 802.3af |
| Led indicator |
Green: Ethernet Red:PoE |
| Working Environment |
Operating Temperature: -20° ~ 55 ° C; Storage Temperature: -40 ° ~ 85 ° C; Operating Humidity: 10% ~ 95%, non-condensing |
| Certification | CE Mark ,commercial; CE/LVD EN60950, RoHS |
| Radiation | CE mark, commercial; FCC Part 15 Class B; VCCI Class B; EN 55022 (CISPR 22), Class B |
| Transmission Distance | Data transmission distance: 100m |
| Warranty | 3 year warranty(1 yeas warranty for power adapter) |
Contact Person: Echo Wang
Tel: +8613760198031
